How Much Allowance for Granite Edge Profiling? Which Kinds Add Material
Granite edge profiling allowance is not one number. There is the machining allowance the saw leaves for polishing, the joint allowance where two profiled edges meet, and the strip allowance for a laminated edge. Only the first and third add material. On a 20mm slab built up to a 40mm edge the strip is 20mm thick and 20mm wide; on a 3000×900 counter run on three edges the strip comes to 0.096 m², 3.6% of the top, and an island exposed on all four edges rises to 5.8%.
How much allowance for granite edge profiling — which allowance do you mean?
Three, and only two of them land on material; the third changes the method, not the square metres. A is the machining allowance: the saw cuts the slab slightly oversize so polishing can true the edge, and it is added to length and width. B is the joint allowance: two profiled edges brought together do not close to zero, but nothing extra is bought — you change the profile or leave a gap. C is the laminated edge strip: a finished edge thicker than the slab needs a separate strip glued under it, and that strip is measured on its own. Roll all three into 'leave 2mm' and B gets added to the slab as if it were size, while C is missed altogether: the tops come in oversize and the strips were never ordered.
| Type of allowance | Where it goes | Who writes it on the order |
|---|---|---|
| Machining allowance | Slab length and width, a little per edge | Buyer, into the slab size |
| Joint allowance | No extra material, change profile or gap | Buyer sets the profile; installer seals the joint |
| Laminated edge strip | A separate strip, measured on its own | Buyer, extra slab for strips |
Does profiling make the slab shorter or narrower?
No. A chamfer and a bullnose both cut the arris on the thickness section, and the outermost point of the slab stays where it was. What changes is the face you measure on. Chamfer a 20mm slab 5×5 and the top face pulls back 5mm from the outer edge: the top is 5mm narrower, the straight face left is 15mm, and measured across the bottom outer edge it is still 600. A full bullnose is different. The arc takes the whole thickness, so the bottom outer edge itself pulls back one R — on a 20mm slab with R10 that is 10mm — and only the apex of the arc stays at 600. So a chamfer is measured on the bottom outer edge and a bullnose on the arc apex. Do not reverse the direction: the top narrows, the outer edge does not pull in, and finished size is quoted at the outermost point. What does take a little off is the truing allowance when a sawn edge is ground to a straight face; that amount is added to the slab at cutting, not deducted from the 600, and with too little allowance at cutting polishing cannot true the line at all.
How much machining allowance, and how is it calculated?
One addition only: finished size + allowance per edge × 2 = slab size. Take a finished 600×300 and assume 2mm per edge: the slab is 604×304, and the area goes from 0.18 m² to 0.1836 m², about 2% more. That 2mm is estimated from the positioning accuracy of the bridge saw and the profiling line; use your own factory's measured figure. It is not an industry standard value and should not be copied as one. Larger pieces and more complex profiles take more truing, so cut two trial pieces from the batch and measure. Too little and the edge line bows; too much and every piece carries a ring of waste that adds up over a hundred square metres.
How much strip does a laminated edge need?
Work it out separately; it does not go into the top area. Finished edge thickness = slab thickness + strip thickness, and the strip thickness is the whole build-up: a 20mm slab taken to a 40mm edge uses a 20mm strip. Strip width is how far the strip reaches in under the top, set by the glue area you want, and 20mm on a 20mm slab. On a counter 3000 long and 900 deep, a run along the three wall-side edges is 3.0 + 0.9 + 0.9 = 4.8m, so the strip is 4.8 × 0.02 = 0.096 m². The top itself is 3.0 × 0.9 = 2.7 m², which makes the strip 3.6% of it. Make the same piece an island exposed on all four edges and the run is 3.0 + 3.0 + 0.9 + 0.9 = 7.8m, the strip 0.156 m², or 5.8%. So do not memorise a fixed percentage: strip area = run length × strip width, and the ratio follows the number of edges — work it out on your own layout. Strips also follow the vein and allow for the saw kerf; round up.
Two bullnose edges butted together — is the joint zero?
No, it is a groove. On a full bullnose R = slab thickness ÷ 2; that is all this article uses, and how the radius is set is covered separately. When two bullnose edges meet, only the outermost point of each touches. The arc falls away by one R on each side, so the groove is 2R wide at the mouth and R deep: on a 20mm slab with R10 that is a V-groove 20mm across the top and 10mm deep. The groove cannot be avoided, only handled: change one edge to a straight face so straight meets straight, or keep the groove and fill it with sealant. Lay out for a zero joint and you get a hollow line down the middle that the sealant cannot fill, and water goes in exactly there.
What happens at a corner, and what do you write on the order?
Run a bullnose to the end and mitre it, and the outside of the corner shows a flat sawn patch where the arc stops. There are only two ways out: leave a straight section at the end for the mitre to land on, or make the corner as a separate piece so the arc runs through. Write two lines on the order. For example: ① Maple Red G562, 20mm, finished 600×300, 6 pieces, long edges A and B full bullnose R10, C and D straight face polished, slab +2mm per edge. ② A separate 3000×900 top from the same 20mm slab: strips 20mm thick and 20mm wide along three edges, 4.8m in total. Set the profile on the built-up 40mm edge — half bullnose R20 on top with a 20mm straight face below, so the glue line sits at the top of the straight face. A full bullnose R20 puts the glue line on the apex of the arc, where grinding runs straight across it, so it cannot be done. Then check three numbers on arrival: outer edge, top face width, straight face height. For line ①, 600×300 with both long edges full bullnose R10, they should read outer edge 300, top 280, straight face 0, with the outer edge taken at mid-thickness, on the apex. Outer edge right but top under 280 means the arc took too much; outer edge right but straight face not 0 means the arc never reached the bottom and the radius is undersize.
