Guangxi Shicai Stone Industry Co., Ltd.

Granite pinhole epoxy filling: the patch fails on trapped air, not on colour

Granite pinhole epoxy filling looks like a colour job and is usually an air job. A pinhole 2mm across and 3mm deep holds about 9.4 mm³, so 1 mL of epoxy fills over 100 of them; what ruins the patch is air sealed under the surface, leaving a thin shell that breaks on the polishing line. Colour decides whether it matches, venting decides whether it stays.

What is granite pinhole epoxy filling actually filling? Separate holes, cracks and porous patches

Start with the conclusion: the difficulty is venting, not colour. A hole is a three-dimensional cavity, a crack is a line, a porous patch is an area, and one epoxy cannot do all three. ① A point pinhole needs a low-viscosity epoxy; if it will not creep into the wall, it seals the mouth only. ② A linear crack needs a medium-viscosity epoxy that presses to the bottom without draining out of the back. ③ A connected porous patch should not be filled: the result is epoxy, not stone. Granite pinhole epoxy filling, then, starts with separating the three before discussing colour; cracks are covered elsewhere. The scale differs too: a crack 0.5mm wide, 100mm long and 30mm deep is 0.5×100×30=1500 mm³, or 1.5 mL, while a hole is a small pocket. The two need different epoxies.

DefectWhat to fill withThe real difficulty
Point pinholeLow-viscosity epoxy that creeps into the wallAir at the bottom has no way out, so only the mouth is sealed
Linear crackMedium-viscosity epoxy that presses to the bottom without drainingNarrow viscosity window: thin drains out of the back, thick will not reach the bottom
Connected porous patchDo not fill; change the block or the sizeResult is an epoxy surface, not a stone surface

Why does a filled pinhole collapse as soon as it is polished?

The air at the bottom of the hole. Epoxy pressed in from above seals that air in; after curing a thin shell sits over a void, and polishing cuts through it, leaving a pinhole-sized dip. The hole is small: one millilitre fills over 100 of them. Three routes: ① drill a vent hole finer than the pinhole from the back of the slab. Set it out from the same two reference edges: measure the hole centre to both edges on the face, flip the slab and measure the same two distances back with left and right swapped, then spot-drill to mark it. Drill in stages, and after each stage push a wire thinner than the vent in from the back; only when the wire shows through the pinhole on the face are the two aligned, and if it does not show, drill again. Aligned, the air has a way out; this route suits slabs whose back is never seen; ② apply low-viscosity epoxy in thin passes, one layer at a time, letting air leave through the wet surface, for shallow holes and for clusters of pinholes where the stone between them is still solid; the porous patch in section 1 belongs in section 4; ③ drill obliquely from the side only where the hole is at the edge and there is still margin before the edge that gets profiled; a hole on the grind line can only be moved or the size changed.

Which state should the colour be matched in?

Match it in the state the buyer will see. One patch has three states: wet epoxy reads deep, cured and dry it lightens, and once polished the gloss returns and the colour deepens back a step. So wet epoxy against the slab reads too dark, a dry unpolished sample reads too light, and neither counts; the sample has to be cured, sanded and polished to the finished state, then compared under the same light. Mixing the colour takes two steps: on an offcut of the same stone, make one sample clearly too light and one clearly too dark, then work between the two toward the slab base colour; cure, sand and polish the chosen one before confirming, and record that ratio so the whole batch is mixed to it. Do not test on white paper or tile: change the substrate and the colour no longer counts. After polishing, also check that the gloss of the patch runs continuous with the slab. Quartz is hardness 7, feldspar 6, and cured epoxy is softer than both, so polishing takes the patch down before the stone around it. Comparison conditions are covered separately.

Stone colourMain riskWhat to look at
Light stone (Sesame White G603)Epoxy yellows, patch reads as a dirty markAfter curing and polishing, compare yellowness against the slab
Dark stone (Sesame Black G654)Gloss does not match, patch reads bright or dullUnder side light, check the reflection is continuous, then face it for hue

Which holes cannot be filled and force a change of block or size?

Four kinds. ① A through hole: epoxy poured at the face runs out of the back and never fills; use it as a drain hole or replace the slab. ② A connected porous patch: the stone between the holes has broken down, so a fingernail lifts powder or whole grains come away; the fill leaves epoxy rather than stone and polishes into a mottled area, so cut the piece smaller. A cluster whose stone between the holes is still solid belongs to route 2 in section 2, not here. ③ A hole at the edge: first measure the width the profiling will remove, then what is left between the hole centre and the grind line. If that margin cannot take a slanted channel, the entry would survive on the finished face, so move the hole inward or downgrade the piece to a shorter cut; if there is room, use the side route in section 2 and keep the entry inside the material that will be profiled away. ④ A hole sitting on a crack: hole and crack meet, load opens it, replace the slab. Filling changes neither the stress nor the stone.

Where does filling sit in the production sequence?

The order is dust removal → drying → filling → curing → polishing → sealer. Sealer comes after filling. Sealer reaching the wall of the hole before the epoxy turns it into a surface the epoxy will not grip, and the fill sits in the hole like a floating plug. In the cold, curing slows, the epoxy stays in the hole longer, the filler settles, and colour varies from top to bottom of the same hole. Use one batch number across a job, because colour can differ between batches. Factory filling happens before polishing; site filling can only be matched to the finished state. A filling batch cannot be scheduled on the 5-day lead time of ordinary slabs: there is a fill and a cure wait to add.

How do you write filling into the order and the inspection?

Four checks. ① Stand at the slab and rake a light almost parallel to the face. Separate the two kinds of dip: one the size of the hole mouth, ringed by a bright edge, means air underneath; a patch sitting a step low across its whole area with the gloss breaking at its rim is epoxy polished down. ② Wet only the patches you put in group one in ①, the ones with air underneath: water drawn into the inner area and spreading as a dark patch means the hole is not full or the shell has broken. A water line that hangs only on the step at the rim, with the inner area unchanged, is a patch polished a step low, not a defect. This step finds voids; it does not judge colour. ③ Press the patch with the back of a fingernail or the rounded corner of a hard plastic offcut, then push gently along its edge: no sinking and no tack means it is cured. Do not scratch: the epoxy is softer than the surrounding quartz, and a scratch will fail a sound patch. ④ Keep a filled sample from the same batch and hold it against the delivery. Three questions for the enquiry: how many passes, which epoxy, what state the sample is supplied in. A sample is what you can hold against the stone; a photograph or a verbal assurance cannot replace it.

WhatsAppEmail us