Granite Stair Corner Piece Size: Lock Three Things, Then Draw the Bounding Rectangle
A granite stair corner piece is sized from three things: the clear width of both flights, the tread depth of both flights, and whether the corner is one L-shaped piece or split into winders. A one-piece L needs a (W+T)×(W+T) block with a T×T notch, so W=1200 and T=300 means a 1500×1500 block and 2.16 ㎡ of stone. Maple Red G562 is stocked in 30mm standard sizes, 5 days to ship; corner pieces are scheduled separately.
How do you size a granite stair corner piece? Lock three things before you talk fabrication
Three numbers settle a granite stair corner piece: the clear width of each flight, the tread depth of each flight, and whether the corner plus one tread on each side is cut as one L-shaped piece or split into winders. Until those are fixed there is nothing to quote, draw or schedule. A corner is not a wider straight tread: a straight tread is parallel-sided, while a corner receives both flights, so its outline is either an L with a notch at the inner corner or a set of winders at different angles, and that is what keeps the joint off the spot where people put their feet. Draw the plan first: extend the two flight lines until they meet, and the square they enclose gives W; measure one tread depth T out from that square along each arm, join the four points, and you have the outline.
For a one-piece L, how big does each arm have to be?
A single bounding rectangle describes the whole L, which is the corner square plus one tread depth along each arm: W+T on a side, with a T×T block removed at the inner corner. Area = W² + 2WT, or W×(W+2T). At W=1200 and T=300 the rectangle is 1500×1500 and the area is 1.44+0.72=2.16 ㎡, the 2.25 of the square less the 0.09 notch. The slab gives up a 1500 square for this single piece, the strips outside it are fixed in width by that square and can only carry smaller items, and the 300×300 notch is cut out and dropped, so yield is poor, which is why a corner piece is priced by the piece. The three rows below only show the arithmetic; put your own W and T in and run it again.
| W, clear flight width (mm) | T, tread depth (mm) | Bounding rectangle (mm) | Area (㎡) |
|---|---|---|---|
| 1200 | 300 | 1500×1500 | 2.16 |
| 1200 | 280 | 1480×1480 | 2.112 |
| 1500 | 300 | 1800×1800 | 3.15 |
If the corner is split into winders, how many pieces and how is each laid out?
Split by equal angle: a 90° corner into n pieces gives each a central angle of 90°÷n. Inner arc = ((90°÷n)÷360)×2πr_in; the outer arc uses the same expression with the outer radius. Within one piece the inner arc is short and the outer arc long, so the shape is a wedge and foot room widens from the inner edge outward. The order of decision runs like this: measure the inner radius first, work out the inner arc of one piece with that expression, compare the result against the minimum tread width the stair code requires where the project is built, and if it falls short add one piece, raising n by one, then run it again until it passes. The code supplies the figure; this page supplies the order. More pieces means a smaller angle, an inner arc closer to the outer one and steadier footing, at the cost of more joints, and every joint needs its edges dressed and its veining matched to the neighbour.
What if the two flights differ in width, or the corner is not 90°?
When the flights differ, the corner zone is W1×W2 and the bounding rectangle is (W1+T1)×(W2+T2), no longer a square; only if the shop insists on a single block do you take (Wmax+T)×(Wmax+T) from the wider flight, and the narrow arm already sits inside that block — the extra is offcut, not a filler. Keep that joint on the wall side, off the walking line. Do not save a piece by stepping the L: a stepped edge puts two sharp points into the corner, and both handling and foot traffic chip them. If the corner is not 90°, the L premise fails: the arms no longer sit in a square, so either go to winders or draw the piece from a site template. For a spiral stair, give the radius and the centre point; without them the shop cannot draw either arc and will send the drawing back. Put the centre on the column or balustrade axis, not on the finished surface.
What numbers go on the order drawing?
A corner piece drawing carries six items only; flights, riser height and tread width belong to the straight-run drawing and should not be mixed in: the width of each arm, the depth of each arm, the notch size or corner angle, which edges are seen and get dressed, which edges sit against a wall, and where the joints fall. Mark the two widths and the two depths separately. A single 1200 by 1200 figure is the corner square, not the piece: at W=1200 and T=300 the block is 1500 by 1500, and what goes missing is the 300mm arm on each side. Leave the notch off and the shop will cost the full block, and you pay for the stone and the weight that gets cut away. Draw the seen edge and the wall edge on separate lines; dress the wrong side and you deliver a polished face to the wall.
| What to mark | How to write it | What goes wrong without it |
|---|---|---|
| Width of each arm | W1 and W2 separately, in mm | Cut as a plain block, four corners too many |
| Depth of each arm | One T for each arm | Joints step out of line when the arms differ |
| Notch or corner angle | 300×300 notch, or mark 90° | Full block is costed; stone and weight both rise |
| Edges seen and dressed | Double line plus the edge profile | Dressing lands on the wall side, done twice |
| Wall side | Draw the wall line | Wrong allowance at the wall; the piece will not seat |
| Joint position | Which pieces join, wall side or outer | Joint lands on the walking line |
Why does a corner piece take longer than a straight run?
Stocked 30mm Maple Red G562 (also sold as G4562, and called Cenxi Red) slabs in standard sizes ship in 5 days; corner pieces and straight treads are both cut to the drawing and sit outside that figure, with a corner piece nested on its own first and its date quoted separately. With 20 large saws and 500,000 ㎡ a year, capacity is not the constraint; a shaped piece taking a nesting slot to itself is, plus the notch cut out of the W+T block. Run corner pieces in the same batch as the straight treads — same block, same reference number, so colour and veining carry across; split the batches and the shade shows as a line where the L meets the straight run. Minimum order 100 ㎡: ask how corner pieces fold into that figure before you order.
