What does a granite undermount sink cutout cost? Four stages, and the last one is a slab risk
A granite undermount sink cutout price is four stages, and the fourth is a slab risk: the cutting path, the cutout edge polish, the cleats, and who supplies the stone if the cutout goes wrong. One 1200×600mm top at 30mm is 0.72 m² and about 58 kg; a 700×450mm cutout runs 2.3 m of perimeter and lifts out roughly 25.5 kg of core piece. Per hole, per metre or all-in, each unit silently includes a different set of stages.
What does a granite undermount sink cutout cost? First ask which four stages are inside the price
A granite undermount sink cutout is not priced as a hole, it is priced in stages, and the fourth is a risk: the cutting path, the cutout edge rounded and polished, the cleats under the sink, and who pays for the slab if the cutout is wrong or the edge blows out. Each stage carries its own unit, which is why two quotes for the same opening never line up. Take a top of 1200×600mm at 30mm: the area is 0.72 m² and the weight, at 81 kg per m², is 58 kg (the arithmetic is in our guide to what a square metre of granite weighs). Those numbers belong to the slab and to handling, not to the cutout. Cut one opening of 700×450mm and the cutout perimeter is 2×(0.7+0.45)=2.3 m, while the core piece that comes out is 0.7×0.45×0.03×2.7≈25.5 kg. Those two numbers are the cutout. Area pays for stone, length pays for work on the cutout edge, weight pays for the core piece going to waste. One seller quotes per hole, the next per metre, a third folds everything into the top price. Who is cheaper is the wrong question; which stage went into which box is the real one.
Why does an undermount cutout cost more than a drop-in cutout? The cutout edge is on show
It comes down to one thing: whether the cutout edge is visible on the face of the top. An undermount sink is bonded from below, so the whole ring of the cutout edge sits open on the face. Hands touch it, eyes see it, water sits on it. The cutout edge therefore has to be rounded and then polished back to the same gloss as the top. On a drop-in sink the rim covers the cutout edge all the way round, the cut has to be straight and free of chips, and whether anyone polished it will never show. The test is one line: the extra money sits on whether the cutout edge is seen, not on how big the opening is. A flush-set sink falls between the two: the joint ring still shows, so the cutout edge is polished all the same.
| Method | Cutout edge visible on the face? | What the cutout edge needs | What to ask in the quote |
|---|---|---|---|
| Undermount sink | Yes, the full ring | Rounded, then polished to the top's gloss | Is the cutout edge polish inside this number? |
| Drop-in sink | No, the rim covers it | Cut straight, no chipping | Is this a cut-only price? |
| Flush-set sink | Yes, along the joint ring | Rounded and polished along the joint | Who confirms the joint line before cutting? |
Is a cutout quoted per hole, per metre of cutout perimeter, or all-in?
With the three methods settled, the next question is the unit: settle the unit first, and only then argue about the number, because the unit is what tells you which stage was left out. Per hole suits one-off work with an assortment of matching openings: one number carries the cutting path and the cutout edge. Per metre of cutout perimeter suits volume, because the tool travels the perimeter and the polishing follows the same line: 2.3 m for a single bowl against 4.6 m for a double bowl is a difference in metres a per-hole number cannot express. All-in with the top looks tidy, but the sheet never says which stage went in and which stayed out. On radii the sheet has to pick one convention: the perimeter is stated on the square-corner outline, 2(a+b), and the rounded path is shorter by (8−2π)R, neither credited nor counted twice. Then the arithmetic that ties holes to metres: the 100 m² minimum is 139 tops: those 139 tops carry about 320 m of cutout edge single bowl, or about 640 m with a double bowl. Stock slabs ship in 5 days, and the cutout and the edge polish are scheduled separately.
| Unit | Where it fits | What it silently includes | Where the argument starts |
|---|---|---|---|
| Per hole | One-off work, a few matching openings | Cutting path and cutout edge in one number | A larger perimeter is not re-priced; is a double bowl two holes or one top |
| Per metre of perimeter | Volume, matching openings, double bowls | Cutting path and cutout edge only | Whether the perimeter comes off the drawing or the finished top; whether radii count into the length |
| All-in with the top | One top with one sink | Top, cutout and cutout edge polish in one line | Who pays for a blown-out edge; whether the cleats are in |
Why can't the four corners be cut square? What the radii do to the labour
Read the table above as one sentence: the vaguer the third column, the longer the argument in the fourth at handover, and the question in row two of that fourth column, whether radii count into the length, lands on the shop floor as the corner arcs. The corners cannot be square because the blade is round: stop the cut at the corner point and the disc sweeps past it within the 30mm thickness, about 49mm with a φ110 blade (r=55), derived in Cutting granite without chipping, and a square corner on a cutout books that bite in advance. An undermount cutout follows the radius profile on the sink maker's drawing: R20 on the drawing is R20 off the machine, and the radius is set by the sink, not by what saves stone or hours. The arc costs time, but not in metres: a quarter arc is πR/2, so R20 is about 31.4mm per corner and 126mm over four, while R50 is about 78.5mm and 314mm. Take the same opening from R20 to R50 and the four arcs gain 188mm while the straight runs lose 240mm in total, so the cutout perimeter actually drops by (8−2π)×30≈52mm. The cost is not in the length: it is in switching to a profiling wheel and polishing the arc in short passes, which adds passes and contact area.
Factory cutout or site cutout, what actually differs?
Three things cannot be recovered on site: the machine, the cutout edge, the spare slab. In the factory the profile runs on CNC, waterjet or a copying machine, the path goes from the drawing straight into the program, and the four corner radii are formed in one pass. The cutout edge then goes to the polishing line and is rounded and brought to the same gloss as the face. If the cutout is wrong or the edge blows out, the same batch is still in the workshop and a replacement is cut from stone that matches in colour. On site there is an angle grinder: straight cuts joined section by section, corners dressed by hand. The cutout edge cannot be polished, so the cutout face of a 30mm slab keeps its sanding marks. The stone arrives as a finished top, so a ruined cutout has no second piece from the same batch, only a wait for resupply. The rule: the main sink cutout belongs in the factory, and site work is limited to small holes added later, a soap dispenser or a filtered-water tap, where the bore is small, the position is off to one side, and a small chip never shows.
Which five questions belong on the order, and which four checks settle it on arrival?
Ask in this order. One: is this priced per hole or per metre of cutout perimeter. Two: does it include rounding and polishing the cutout edge, and to what gloss. Three: whose drawing sets the corner radii, and is the R value written into the work order. Four: are the cleats or the support frame included, and how many pieces. Five: if the cutout is wrong or the edge blows out, who supplies the stone. Once those five are answered the sheet holds what it needs. Then four checks at handover. Sight along the cutout edge with a light held low and look for a run of chipping. Run a fingernail around the top arris: it should be round all the way, with no stretch that suddenly catches. Measure both diagonals of the opening; equal diagonals mean the opening is square. Set the sink in and check that the rim meets the cutout edge all the way round, with no grit and no gap left in the joint. If one of the four fails, do not sign.
