Guangxi Shicai Stone Industry Co., Ltd.

Shipping marks on granite crates: eight lines on the front, three on the sides

Shipping marks on granite crates are painted by the shipper, not by the treatment plant. Eight lines go on the front face, three on each side. Those eight are the fields on our own shipping sheet; no standard fixes the count, and the only test is whether somebody actually uses the line, at loading, at transhipment or at the port. A 20ft load of 346 sqm in 30mm runs about 28 tonnes, and tally clerks count it crate by crate.

What should a granite crate's shipping marks say? Main mark first, side marks second

The mark goes in two places. The main mark covers the front face of the crate and carries all eight lines. The side marks go on the two long faces and carry three lines only: product and size, crate number, destination port. The split has a physical reason. Once crates are stacked in a yard, the front face ends up behind the crate next to it, and what stays visible is a side. That is the face a forklift driver and a tally clerk read to work out which crate this is and where it is going. The front mark serves whoever opens the crate and reconciles the weights; the side mark serves whoever has to find that crate in a stack. Neither replaces the other. With side marks only, nobody can match weight or contract number at opening. With a front mark only, the crate might as well be bare in the yard. We paint them ourselves, with a stencil and black paint.

Which eight items go on the front mark, and who uses each one, at the port or earlier?

These eight are the fields fixed on our own shipping sheet. No standard says a mark has to hold exactly eight. The reason to list them is plain: each line is used by someone, most of them after the container lands and a couple before it, and the third column names that person and that job. Set the eight side by side and they do two jobs. Consignee, destination and contract number tie the container to an order on paper. Product, crate number, weights and dimensions let people lift, count and stack the right crate on the ground. Origin sits apart, because that line is read by the importing customs, not by anyone who touches the box.

ItemWhat you paintWho uses it, and for what
ConsigneeCompany short name or code, spelled as on the bill of ladingForwarder matching documents, warehouse sorting by owner
DestinationUnloading port, in its English port nameContainer check at loading, when one factory ships to several ports; devanning and reloading at a transhipment hub
Contract no.The number on your PI or contract, the same on every crateDocument matching, balance payment, claims
Product and sizeEnglish name + code (Maple Red Granite, G562) + L×W×T in mmTally counting, site identifying the stone
Crate no.Contract-C/NO.1-N, one per crate, matching the packing listStripping and counting, finding crate 7
Gross / net weightkg, same figures as the packing listLifting, load planning, floor load per stack
Crate dimensionsL×W×H in cmContainer planning, volume, how many high
OriginMade in ChinaDestination customs, origin check

How do you number the crates so they match the packing list?

Write it as contract number-C/NO.1-N, for example SC2026-0417-C/NO.1-20: the front part is the contract, the back part runs from the first crate to the last. If a container holds twenty crates, N is twenty. Take a 20ft load of 346 sqm in 30mm split into twenty crates, the count following the actual packing and twenty only here to work the sum through: each crate averages 346 ÷ 20 ≈ 17.3 sqm; net weight takes three steps: 346 × 0.03 = 10.38 m³, 10.38 × 2.7 ≈ 28 tonnes, 28 ÷ 20 ≈ 1.4 tonnes a crate, and the gross weight you paint adds the weight of the wood. Two things have to hold: the crate number on the packing list is the number on the wood, crate for crate (the one listed as C/NO.7 carries 7 on its face), and the run from 1 to 20 is continuous, with no gap and no repeat. At destination the tally is done against those numbers, so a single missing number leaves the rest unresolvable. Nobody can tell a short shipment from a counting error, and the whole container gets turned over. If crates are added, merged or renumbered, the packing list changes in the same revision, and the last version governs both sides.

How many faces do you paint? In the stack, usually only the sides show

Front plus two sides, three faces at minimum. The front carries the eight lines of the main mark, each side carries the three lines of the side mark. The fourth face usually ends up against the container wall or turned inward, so paint there is never read. Letters are stencilled in black paint, sized so that a person standing two or three metres away can read them. That test beats a millimetre figure, because the reader is standing on yard gravel with no rule in hand. Brush the sawdust off first, so the paint sinks into the grain. Marks painted across a board joint, a nail head or a strapping band break at the first rub. The strip low on each side is normally where the IPPC stamp goes, so keep the mark clear of it and never put a crate number on top of the stamp.

Why are shipping marks and the IPPC stamp two different things?

Different people read them. The IPPC mark is for customs and plant health: a licensed heat treatment plant brands or stamps it on the wood, and it carries the IPPC symbol, the country code CN, the treatment code HT for heat treatment or MB for methyl bromide, and the plant registration number. Shipping marks are commercial information for the consignee, the forwarder, the tally clerk and the warehouse, and the shipper paints them. Their positions should not collide. The IPPC stamp usually sits low on a side face, so route the mark around that strip and keep the crate number off the stamp, because a smeared stamp is one the inspector will not accept. One line does not move: you cannot paint an IPPC stamp yourself. A self-made stamp is a forgery, and the container can be refused entry or sent back when it is found. Shipping marks are the opposite case, since they belong to the shipper by definition. For how the wood is treated and what makes a stamp valid, see our note on fumigation for stone crates.

How do you write the marking instruction so the factory does not redo the crates?

Write it as a copy sheet, not as a reference. Six things in one email: the five main-mark lines that repeat on every crate — consignee, destination, contract number, product and size, origin — copied with capitals and punctuation intact; the three that change crate by crate — crate number, gross and net weight, dimensions — set out as a variable table, one row per crate, the run written through to the last crate, weights and dimensions filled in after the crate is closed and weighed rather than estimated, with product and size moving into that table when one container mixes sizes; the three side-mark lines; the crate number run and the packing list version it belongs to, noting that each crate carries only its own number; three faces, black paint, stencil lettering, sized to read at two or three metres; and the strip low on the side kept clear for the IPPC stamp. Add one return step: once the crate is closed and weighed and the weights and dimensions are painted in, photograph the front and one side, and release the crate only after the photos check out. A line the instruction leaves open is a line the factory fills in its own way. Maple Red becomes Red Maple and 30mm becomes 3cm; neither is caught at loading, and the buyer or the tally clerk spots it on the crate face later, so the paperwork has to be corrected. So the product and size line goes into the email in bold, spelled Maple Red Granite, G562, followed by the size, with copy exactly, do not reword written beside it.

WhatsAppEmail us