Guangxi Shicai Stone Industry Co., Ltd.

Granite Back Coating Before Installation: the Back Face, the Four Edges, and Why the Finished Face Stays Bare

Granite back coating before installation goes on one face: the back face (bedding face). The four edges usually follow, the finished face stays bare, and cut edges or drilled holes are touched up after fixing. This is a film-forming barrier against alkali, not the penetrating six-sided sealer. On a 600×600×30 slab the edges alone equal 20% of the back face.

Which faces does granite back coating before installation actually cover?

One face is mandatory: the back face (bedding face). The four edges normally follow it, the finished face is never coated, and cut edges or drilled holes get a touch-up after fixing. The reason is mechanical, not cosmetic: an alkali-resistant back coating dries into a film, and that film sits between the cement mortar and the stone, so water and alkali never reach the capillaries. Any face that touches the mortar therefore needs it. Read the table as one sentence: coat the faces alkali comes in through, and leave bare the face that has to take the polish.

FaceCoated?Why
Back face (bedding face)AlwaysCement mortar sits directly on it; alkali and water enter here
The four edgesUsually, togetherSame sawn cut edge, capillaries open; pale slabs whiten from the edge first
Finished faceNeverThe coating films and carries colour, dulls the polish, and seals alkali inside
Cut edges and drilled holesTouch-up after fixingA section cut on site carries no coating

Why does efflorescence always start from the back face?

Because that is the direction the alkali travels. Cement hydrates into calcium hydroxide, and water carries it along the open capillaries of the back face (bedding face) toward the finished face. Near the surface it meets carbon dioxide in the air and becomes calcium carbonate; that is efflorescence. The bloom shows on the face, but the road starts at the back. The arithmetic is short: on a 600×600×30 slab the back face is 0.6×0.6 = 0.36 m², the four edges are 4×0.6×0.03 = 0.072 m², so back plus edges come to 0.432 m², and the edges alone equal 20% of the back face. Small as that share is, the edges are the water entry left exposed between slabs, and that is where the bloom usually starts. The cost of a missed edge is not measured in area; it is measured in whether that edge is a way in. Pale stones (Sesame White G603, Wave White G418) show it first; on Sesame Black G654 it still happens, you simply cannot see it.

When is it required, and when can it be skipped?

Sort by fixing method; the test is whether the back face touches alkaline mortar. Wet fixing beds the back face in cement mortar or adhesive, so the back coating is mandatory. Dry hanging leaves the back face in a cavity with no mortar contact, so there is no back coating. Keep this separate from the six-sided sealer: the sealer is penetrating — it soaks into the pores and makes the stone repel water without changing the surface; the back coating is film-forming — it lays a membrane on the back face to block alkali. A wet-fixed slab usually takes both: sealer first, then the back coating once the sealer has cured, because a film applied first would seal the pores and keep the sealer out; take the interval from the longer of the two data sheets. On dry-hung work, add a back coating only where joint grouting or backing mortar reaches the back face. Inside wet fixing, more water means more urgency: plaza paving, wet-fixed facades, bathrooms and pool surrounds. Dark stone gets coated too, because 'you cannot see it' is not a test — once efflorescence sits on Sesame Black G654 it does not wash off either, it just hides during inspection. Spot-fixing and semi-dry-hanging sit in between: the back face still takes adhesive dabs, so judge them as wet fixing, not as dry hanging.

What about the edges, cut edges and drilled holes?

Coating the edges is about closing the cut, not about appearance. The four edges are sawn like the back face and never polished, capillaries wide open, so they go on with the back face; on a 600×600×30 slab the four edges come to 0.072 m², a fifth of the 0.36 m² back face, but skip them and you leave a straight channel into the slab. Every section cut on site needs a touch-up: cutting to size, core drilling, edge trimming, and corners chipped in transport, because the stone under a fresh cut is raw. We coat the back face right to the edge, with no bare strip. The 3 to 5 mm left bare sits on the side edge just below the finished face. That strip is not bare stone — the penetrating sealer already covers it; the back coating simply stops at the arris instead of running over it. That is shop practice at Guangxi Shicai Stone Industry Co., Ltd., not a specification value. A back slot is where a dry-hung bracket sits. Dry-hung slabs get no back coating anyway, so this only matters on slotted dry hanging that is also grouted: keep the slot walls and base bare per the fixing drawing, and keep both the back coating and the six-sided sealer out of it, because either one weakens the structural adhesive; the bracket positions are the same. The patch where grouting or backing mortar meets the back face does get a touch-up, and that is a different location from the slot; where grout actually runs into the slot, the fixing drawing wins. Coats, the interval between them, dilution and coverage rate all come from the product data sheet — products differ widely, so do not work from a verbal recipe.

How do I check on arrival that it was done, and done right?

Five checks, in order: (1) look at the dry film — even colour, no missed white patches, no runs onto the finished face; (2) run a finger along the four edges and feel for stretches with no film; (3) divide the area by the coverage rate (m²/L) on the data sheet to get the litres you should have used — a figure that does not add up means the coat went on thin or was missed, and that says more than a patchy colour; (4) sample three cut edges or drilled holes and check the inside walls; (5) keep a reference slab from the same batch for repeat-order comparison. Runs onto the finished face are the usual rework. A film that has not cured reads darker, so wait out the curing time on the data sheet before judging.

WhatsAppEmail us