Guangxi Shicai Stone Industry Co., Ltd.

How do you work out granite freight cost per ton? Divide the container total by the tons actually loaded

What does granite freight cost per ton actually mean? It is not a rate a forwarder hands you: a full container is priced per box, so you divide that box's total cost by the tons inside it. For the same box money, 8.1 t loaded carries a ton price 3.46 times the full-load figure. Compare thicknesses per square meter, suppliers per ton.

How is granite ocean freight calculated per ton?

Ocean freight for a full container is not priced by the ton, it is priced by the box. The per-ton figure you hear is not a rate from the forwarder, it is a division you do yourself: one container's total cost divided by the tons that container actually carries. Same 20ft box, same route: loaded with 28 t or with 8.1 t, the container cost stays the same while the tonnage falls to under a third, so the ton price comes out 3.46 times higher. The ton price is a function of loading rate, not a property of the stone or the route. Before comparing quotes, ask which basis you are being given: per container, or per ton; and if per ton, whether the denominator is actual loaded tons or the 28 t full load. This article takes 28 t as the full load for a 20ft box; that is a common payload ceiling that varies by carrier and route, so confirm it in writing at booking.

Why can the freight per ton vary by more than three times in the same container?

Because the container's total cost is charged per box and does not follow the tonnage. Ocean freight, origin handling, documentation and seal are fixed on one box: load ten tons less and none of them shrinks, so a smaller denominator gives a larger quotient. Take 28 t as 1.00, and 8.1 t gives 3.46; the two middle rows are in the table. 8.1 t is 100 m² of 30 mm slab and 16.2 t is 200 m²; how they arise is worked through in LCL vs FCL for granite shipping; this article borrows them for one point: divide the same container money by different tonnages and see how far the ton price moves. The table shows ratios, not prices: multiply your own container total by them to reach your ton price. Read the table as one sentence: the loading rate supplies the multiple, the container price supplies the base figure — route, ports and carrier all sit on the container price side, and inside one box the loading rate is what you can move.

Weight loaded tShare of one box's payload (28 t)Freight per ton (full load = 1.00)
28.0Full load1.00
21.075%1.33
16.258%1.73
8.129%3.46

How many tons does one square meter come to? Work out the denominator first

One square meter converts to tons by thickness alone: thickness in metres times 2.7. That gives 0.081 t at 30 mm and 0.135 t at 50 mm. Only once you have that denominator does a ton price mean anything. A box takes fewer square meters as the denominator rises: at 28 t full load a box takes 346 m² of 30 mm and 207 m² of 50 mm (28 ÷ 0.135 = 207.4). The 346 figure is not an estimate: it is the loading record for our Maple Red G562 (code G4562, also traded as Cenxi Red) 30 mm polished slab, the same number stated on the product page, and it matches 28 ÷ 0.081 = 345.7. Use the same formula to check any claim: if square meters × thickness × 2.7 lands at or above 28 t, it has to be re-checked against the verified gross mass (VGM), never pushed to the limit on paper — our 346 m² works out at 28.03 t, already on the line, which is why the figure we declare at loading comes off the weighbridge, not from 346 × 0.081.

When does comparing by the ton mislead you?

It goes wrong when you cross thicknesses. A 30 mm and a 50 mm slab can carry an identical ton price, because the box costs the same and both sit at the same 28 t load; yet for that same box money you get 346 m² of 30 mm and 207 m² of 50 mm, which is 1.67 times on a square meter basis. Look only at the ton price and you conclude thick and thin cost the same, when the square meter is two thirds dearer. The other way round, between suppliers at one thickness, the ton price is the clean basis, provided both quotes share the same denominator and cost scope: net stone weight for both, delivered to the same port; if not, bring both onto one basis first. Read the table as one sentence: change the thickness and the ton price does not move, the freight per square meter moves first. The 50 mm row is a conversion reference only: our G562 is regularly produced at 30 mm, 50 mm is scheduled separately and priced against its own load.

ThicknessWeight per m² tm² per box at full loadFreight per m² at full load (30 mm = 1.00)
30 mm0.0813461.00
50 mm0.1352071.67

How many kinds of ton sit on the quote, and which one are you asking about?

Three: net stone weight, gross weight, and chargeable ton — mix them and the arithmetic fails. Net weight counts stone only and is what you size material with. Gross weight adds crates, dunnage and pallets, it is what customs and weight limits look at, it is always larger than net, and the gap is packaging. The chargeable ton is the billing unit small shipments build from W/M; that method has its own article and is not repeated here. To work out a ton price yourself, the denominator should be net stone weight or the actual weighed load, never gross weight: gross puts packaging into the denominator, so the ton price looks cheaper while the loading rate you assumed is overstated. Find the three columns on the quote you already hold: which one is net weight, which one is gross, and whether chargeable tons appear at all. If you cannot point to them, the quote is not yet comparable.

Which numbers do you ask the forwarder for, so you can work out the ton price yourself?

To reverse a ton price out of a container bill, split the basis into numerator and denominator, four figures, two on each side. On the numerator: is this box priced as a flat container rate or per chargeable ton (W/M) — get that wrong and the numerator is wrong; and how far does the price reach — origin loading, documentation and seal included or not, which charges fall due at destination, and how overweight or shortfall surcharges are applied. On the denominator: how many square meters this box actually carries, answered against your slab thickness rather than a vague one container; and net stone weight and gross weight reported separately, so you can tell which denominator their ton price used. With the four in hand, divide the container total by (square meters × thickness × 2.7) yourself, entering thickness in metres, not millimetres; if the two figures disagree, check the denominator for gross weight first, then the numerator for missing destination charges.

WhatsAppEmail us