Guangxi Shicai Stone Industry Co., Ltd.

Undercut Anchor for Stone Cladding: How Much Stone Is Left Under the Hole?

Choosing an undercut anchor for stone cladding starts with arithmetic, not with the bracket. On a 30mm slab at a 12~15mm hole depth, 15~18mm of stone remains under the hole; a 20mm slab at the same depth leaves 5~8mm. Read the sample's hole depth first, then check your thickness.

How is an undercut anchor different from a kerf-slot fixing?

The difference is where the load lands. A kerf-slot fixing hands the load to the two shoulders at the slot on the panel edge; an undercut anchor hands it to a ring of stone at the back face, where the hole is widened. The panel edge is the narrow face of a slab and the place where chipping usually starts, and a slot cut into the narrow face, centred in the thickness, leaves one shoulder on each side of it; those two shoulders are the whole bearing surface, and they are thinner than the original edge. An undercut anchor never touches the panel edge, so all four sides stay whole, and that is what you are paying for. The cost sits in the same place: the hole enters the stone from the back, so a hole drilled off line, too deep, or with a broken undercut scraps the slab outright, while a slot cut slightly wrong can still be re-glued or re-cut. Undercut work gives no second chance after the drill. The other route is kerf-slot fixing, and how deep that slot should be is covered in the kerf depth article.

ItemKerf-slot fixingUndercut anchor
Load pointTwo shoulders at the edge slotRing of stone at the back face
Panel edgeSlot centred, one shoulder each sideLeft untouched
If it goes wrongCan be re-glued or re-cutSlab is scrapped
Limited byThickness of the two edge shouldersRemaining thickness under the hole

How deep should the hole go, and how much stone is left?

One formula: remaining thickness = slab thickness − hole depth, with the depth read at the deepest point of the undercut, not at the bottom of the straight hole. On a 30mm slab the hole depth usually lands at 12~15mm, which leaves 15~18mm. That is a common shop range and an experience value rather than a code figure; the real reference is the hole depth your bracket sample calls for. Whether it is enough is set by the maker: the sample states a slab thickness and a hole depth, and the difference is the remaining stone you must keep. Ask for both numbers with the quote; if they do not fit your slab, change the slab or the anchor, and if you cannot get them, do not place the order. Why it is a hard limit: when you tighten, the cone pushes the sleeve outward, and the only thing resisting is the layer of stone under the hole. Edges, adhesive and bracket do nothing here. Too thin and a small flake leaves the face, which reads as a shallow pit from the front, and the slab is already scrap. So take the sample's depth first, check it against your slab, and if it does not fit, change the bracket or change the thickness. Drilling deeper moves the wrong way.

Which numbers have to go on the processing order?

Five: straight hole diameter, hole depth, undercut diameter, hole centre to panel edge, and hole positions. Write positions as dimensions from the panel edge, never as centred, because four holes on one slab read four different ways in the shop once the word centred is used. Why not write to the undercut standard: the anchor, the undercutting tool and the gauge are one matched set from one maker, and mixing them puts the undercut diameter out of step with the sleeve. Anchor small, tool large, and the opened sleeve never reaches the step, leaving friction only. Anchor large, tool small, and it will not go in; forcing it splits the hole bottom. Add squareness: tilt the hole axis and the anchor loads eccentrically, crushing one side of the hole bottom first. Squareness comes from a drill stand, not a hand drill.

DimensionSet byUsual range on a 30mm slab (experience)Site check
Straight hole diameterDrill matched to the anchor shankSame size band as the shankPush the shank in; it should seat without wobble
Hole depthDepth stated for the bracket sample12~15mmDepth gauge to the deepest point of the undercut
Undercut diameterUndercutting tool, matched to the sleeve2~3mm larger than the straight holeRun the gauge through; if it will not pass, scrap it
Hole centre to panel edgeEdge distance on the hole layoutAs drawn; measure all four edgesTape from hole centre to each of the four edges
Hole positionsFour-hole layout on the drawingSame layout on every slabMeasure both diagonals; the two numbers should match

Can a 20mm slab take an undercut anchor?

Do the arithmetic first. A 20mm slab at the same 12~15mm depth leaves 5~8mm; a 30mm slab leaves 15~18mm, more than double. That remaining layer does not only carry the tightening load. When wind pulls the panel outward, the ring under the hole is in local compression, and the force has to travel back through the same layer into the panel. A 30mm slab weighs 81 kg/㎡, so a 600×600 panel at 0.36 ㎡ is about 29kg, and that self-weight sits on the same spot. So the question is not whether a 20mm slab can be drilled, but how little stone is left afterwards. Choosing the overall thickness is a separate question; on the undercut line, thickness is the gate, and no bracket makes up for it.

How do you choose the bracket?

Three things, plus one more. Material: stainless steel on exposed outdoor work, with a higher corrosion grade on the coast or in industrial air. The coating on galvanized carbon steel is broken at cut edges and threads, rust starts at those breaks, and rust takes more volume than the steel it came from, so it swells against the hole wall and can split the undercut. Adjustment: slotted holes plus adjusting bolts give correction in three directions: in and out, left and right, up and down. If the adjustment runs out and the panel still will not sit flat, the error is in the substrate, not the bracket. Compatibility: buy the anchor and the undercutting tool from one supplier. Then the one often left out: the pull-out test. The figure on a sample sheet comes from a laboratory, and on site you run a set per batch. Without that set, every dimension above is only plausible.

What do you send with an enquiry, and what do you check on delivery?

Four items with the enquiry: slab thickness, panel size, a hole layout drawing with hole centre to each edge, and the bracket model or a sample. Add the surface finish, because a flamed face chips at the hole mouth more readily than a polished one, so the same depth behaves differently. On delivery, check five numbers: hole diameter, hole depth, whether the undercut step is there, remaining thickness, and hole position deviation. The first two take a caliper and a depth gauge, the third an eye and a gauge, the last a diagonal measurement; remaining thickness needs no separate reading, since thickness minus depth gives it. We run 30mm slabs, 100 ㎡ minimum, 5 days for regular sizes, and cut undercut holes to the customer's bracket as a first piece, with batch work only after that piece is signed off. The plant has 20 saws and capacity for 500,000 ㎡ a year.

WhatsAppEmail us