How many pieces in a granite bundle? Two limits decide it, not a fixed number
There is no standard count of pieces in a granite bundle. Pieces per bundle is the bundle weight limit divided by the weight of one piece, rounded down. On a 1 tonne line, 600×600 at 30mm gives about 34 pieces and 300×600 about 68. One tonne is only an example; the real limit has two gates: weight, the lower of forklift capacity and pallet base, and width, which has to clear the 2350mm internal width.
How many pieces actually go into one bundle?
There is no single number. The count is the bundle weight limit divided by the weight of one piece, rounded down. On a 1 tonne control line, 600×600 at 30mm gives about 34 pieces, 400×400 about 77, 300×600 about 68 and 1000×600 about 20. The whole spread comes from piece weight, not from packing habit. That is why a supplier asked how many pieces go in a bundle has to ask your size and thickness back before he can answer. One tonne is a control line used as an example in this article, not an industry standard; set yours by your forklift's rated capacity and the pallet base.
| Size | Area per piece | Weight per piece (30mm, 2.7 t/m³) | Pieces per 1 tonne bundle |
|---|---|---|---|
| 600×600 | 0.36 ㎡ | about 29.2 kg | about 34 pieces |
| 400×400 | 0.16 ㎡ | about 13.0 kg | about 77 pieces |
| 300×600 | 0.18 ㎡ | about 14.6 kg | about 68 pieces |
| 1000×600 | 0.60 ㎡ | about 48.6 kg | about 20 pieces |
Why does the count change so much from one size to another?
Because the count runs in inverse proportion to piece weight. At 30mm a piece weighs its area times 0.03 m times 2.7 t/m³, so double the area, double the weight, and the number of pieces a bundle holds halves. 600×600 is 0.36 m² at about 29.2 kg and 300×600 is 0.18 m² at about 14.6 kg, so the first is exactly twice as heavy and the count exactly half: 34 against 68. Use that ratio as a check. If the counts a supplier quotes do not follow the weight ratio of the sizes, his weight limit is not the same as yours and the two figures cannot be compared. It also means fragmented sizes are expensive to count: the same area arrives as far more pieces. The Sesame Grey G602 we pack at 30mm follows the same rule, and the count moves with the size.
How heavy should one bundle be?
Two gates have to clear before the count means anything: weight first, then width. Inside the weight gate you take the lower of two ceilings. The first is the rated capacity of whatever unloads the bundle: a forklift, a crane or a truck-mounted loader lifts only so much, and this is a hard ceiling, so work it out first. The second is the pallet base and the strapping: the number and section of the bearers and the number and tension of the straps decide whether the bundle survives a lift, and no strap holds a weight the base cannot carry. The lower of those two tonnages is the weight limit, not an average and not another plant’s habit. Width is a separate gate: the container gives about 2350mm inside, and a bundle too wide will not sit two abreast. Small sizes hit this gate first: 77 pieces of 400×400 at 30mm stand 2310mm, leaving 40mm of the 2350mm width, so only one bundle goes abreast; to keep two abreast the count has to come down until the pair plus edge protection still clears 2350mm.
How is the bundle width worked out?
Width is the piece count times the slab thickness, because slabs stand on edge and each one takes up one thickness. 34 pieces at 30mm is 34 times 30, or 1020mm. The container gives about 2350mm inside, so two bundles at 1020mm make 2040mm and fit, while a third would need 3060mm and does not. The remaining 310mm or so is not empty space: edge protection, straps and dunnage all live in that gap, holding the pair across the container so they do not shift at sea. So the count governs width as well as weight. A 600×600 bundle on edge stands about 600mm tall: three layers make 1800mm, while a fourth needs 2400mm against 2390mm of internal height, so three is the ceiling; two abreast and three high, with 9 rows along the 5.9 m length at 0.6 m per bundle, gives 54 bundles by geometry, while the 346 m² we load per 20ft container at 30mm works out at about 28, so weight still fills first. Push the count too high and the width overshoots, the stow drops from two abreast to one, and the load has to be replanned.
What goes wrong when the piece count is left vague?
Three places. Settlement: on a per-piece order the count is the figure the rate is multiplied by, and two pieces short on each bundle, over dozens of bundles, is a real gap that nobody can later trace to a short load or a counting error. Replenishment: a repeat batch has to match shade and thickness, and you need the original count per bundle and the original width so the new bundle fits the same slot and lines up with the old count. Receiving: the tally is bundles times pieces per bundle, and if either factor was given verbally the total will not match the packing list, and the cargo gets blamed for a number that was never written at the source. Put the count in the pieces-per-package column of the packing list, tied to the crate number, not in the description line.
How do I fix the count with the supplier before ordering?
Put four lines in the contract or the order annex, not in the body of an email. Line one is size and thickness, because that sets piece weight. Line two is pieces per bundle, as a fixed number that may not be broken up. Line three is net weight per bundle or the weight limit, with a note on where the figure comes from, forklift capacity or pallet base. Line four is bundle width and how many bundles go abreast, checked against the 2350mm internal width. Add the settlement basis: per piece or per square metre, and if per square metre, say the count is only for tallying. With those four lines the supplier packs to the number and you check the load against it; miss one and three stages each invent their own explanation. We run a 100 m² minimum with five days to ship, so packing has to be settled the day the order is placed.
