Should mesh backing come off a granite slab? Wet fixing strips the whole sheet, dry fixing cleans the fixing points only
Mesh backing removal on a granite slab comes down to one question: will the back still touch cement-based material once the slab is installed? Wet fixing means stripping the whole sheet to bare stone. Dry fixing means cleaning the fixing points only. In 100 m² of 600×600 that is 278 slabs, and the labour is counted per slab, not per square meter.
Should the mesh backing be removed from a granite slab? Look at where the slab goes first
One thing decides whether the mesh backing comes off: will the back of this slab still touch anything containing cement in the finished work? If it will, strip the whole sheet. If it will not, the mesh can stay. Dry fixing sits between the two, where the sheet stays and the fixing points are cleaned back to bare stone. The table below splits this by four uses: two wet fixing rows are full removal, the dry fixing row is fixing points only, and the countertop row can keep the mesh.
| Where it is used | Remove the mesh? | How far to clean | What happens if it stays |
|---|---|---|---|
| Floor, wet fixing (mortar or tile adhesive) | Strip the whole sheet | To bare stone, resin scraped off | Mesh and resin become a separating layer: the mortar grips the net, not the stone, and hollow spots start here |
| Wall, wet fixing | Strip the whole sheet | Same, and it must be finished before any back coating | The coating film lands on the net, so the alkali barrier never reaches the stone |
| Dry fixing (kerf slot, back bolt) | Full removal not needed | Clean the fixing points only: inside the slot, inside the hole, under the pad | Structural adhesive bonds to resin, leaving one layer between bracket and stone |
| Countertop, window sill (back meets no cement) | May stay | Clean the seams, cut-outs and polished edges | Resin sits exposed at the seam, and the joint adhesive cannot bite into stone |
What is mesh backing for? Why glue a net to the back of a sound slab at all
Read the table above as one sentence: whether the back meets cement decides whether the mesh comes off. Mesh backing is a glass fibre net glued to the back of the slab with resin. It holds the sheet together while the slab is moved, cut and shipped, so material with hairline cracks or heavy veining does not break on the way. It is not a structural layer that strengthens the stone, only temporary insurance. Wave White G418 is produced in 30mm, and one 600×600 slab weighs about 29 kg: two people can lift it, yet one corner knocked against a stillage is enough to open a vein. Once the slab is on a wall or on the ground, mortar or brackets take over the load and the net has no job left. Whether the mesh sits flat is easy to check on arrival: run a hand over the back and look for lifted edges. The question is therefore not whether the net is any good, but whether it should survive into that stage.
Why does wet fixing make removal unavoidable?
Because the mortar ends up gripping the net, not the stone. Glass fibre and resin do not absorb water and do not bond with cement paste, so the mortar only grabs the weave. Between the net and the stone there is nothing but the resin film, and that film is what ages and what moisture attacks. When it lets go, the whole mesh sheet comes off the back of the slab, with the mortar still stuck to it; that is where hollow spots begin. The film is the weak layer in this job from the start, and on a wet-fixed floor or wall the moisture arrives through the back, so nobody sees the film let go until the slab sounds hollow. Check the film first, before blaming the mix or the trowel hand. The second cost is the back coating: coating applied over the mesh is coating that never reaches the stone, so alkali and water enter exactly where the barrier is missing. Removal is subtraction. Tensile strength returns to the stone itself, and a 30mm slab carries itself.
Can dry fixing leave the mesh alone? Which spots still have to be cleaned
Dry fixing does not need full removal, because the back faces an open cavity, never meets mortar, and the resin is never kept wet. Three spots must still be cleaned to bare stone: inside the kerf for the slot fixing, inside the back-bolt hole, and the small area the pad presses on. These are where structural adhesive and brackets actually carry load. Adhesive spread on resin leaves a resin interface between bracket and stone, and the load has to cross it before it reaches stone; that interface grips resin, not stone, and none of it depends on how new the adhesive is. Cutting the slot or drilling the hole has already torn the net, so trim the loose resin at the cut edge instead of leaving a flap hanging over the kerf. Clean those three spots with a scraper and a small grinding point, never by running a disc across the whole face: chip a kerf edge on a 30mm slab and that piece is scrap. For 100 m² in 600×600 that is 278 slabs, and cleaning three spots is a different job from stripping a whole face; quote the two separately.
How clean is clean enough, and how do you strip a slab without damaging it?
Clean enough means bare stone. Run a hand across it and you should feel grit, not the slip of resin, and under raking light there should be no glossy film. Work a scraper over the face first, then take what is left with a grinding disc, pushing in one direction instead of spinning in place; heat softens the resin and it smears rather than lifts. Blow the dust off and look again. For acceptance, pull three slabs at random and turn them over; a glossy film on the back means the disc never reached it. Do not soak the back in solvent. Solvent softens the resin and carries it into the capillary pores, so the surface looks clean while the glue has moved into the stone, and hollow spots and efflorescence follow the wet fixing. Thin slabs and heavily veined material need a decision first, because the answer changes with the fixing method. Strip the edge as well, since a disc that takes half the net off a chamfer leaves a fringe on the arris.
How do you word the enquiry and the work order so that "mesh removal included?" cannot be dodged?
Write the location, the degree and the count. Leave one of the three out and there is nothing to inspect against. Location means the use: floor wet fixing, wall wet fixing, dry fixing or countertop, one of four, not the phrase "remove mesh". Degree means bare stone, with the resin scraped off and finished by disc. Count means pieces: 100 m² in 600×600 is 278 slabs at 0.36 m² of back each, so the labour is spread over 278 pieces. A line that says only "100 m²" leaves the factory and the site calculating different numbers. Add three questions: is removal inside the processing charge, is it done at the factory or on site, and does it fit within the 100 m² minimum and the 5-day dispatch.
